Showingof 104 item(s)
Use stilts to keep your fully glazed wares from sticking to the shelf during the firing process. Measurements are from metal point to metal point. Made in the USA.
C$2.10
One proper application of Mayco Kiln Wash will remain effective through multiple firings, increasing the working life of the kiln shelf.
C$18.00
Includes 15 stilts in a variety of sizes from the "Heavy Duty Series". Great for wares that need a little extra support. Please see below for further information and stock availability.
C$42.00
A wiring harness is a complete kit of every wire and connector in your kiln, pre-cut to size, colour coded, labelled, and with connectors crimped on at the factory.
C$210.00
* Please see notes at bottom of page before ordering.*
Tube Assembly for Dawson Kiln Sitter.
Tube Assembly for Dawson Kiln Sitter.
C$110.00
Switch wire per foot . Available in 12 Gauge in Red, White and Black. Specify colour in the notes section at checkout.
C$3.55
Bead Racks and Bead Trees are an excellent way to hold up your work in a kiln firing. By suspending small forms from an interior unglazed hole, you can glaze the entire exterior of your piece for that crisp, all-over glazed finish!
C$78.50
A sample of 15 of The Ceramic Shop's top sellers. 1 each of the stilts shown in picture, as follows:
#0, #1, #2, #4, #6, #8, #3B, #4B, #5B
#6H, #15-4, Ring #4, #4x6, #10x15, #12x6
#0, #1, #2, #4, #6, #8, #3B, #4B, #5B
#6H, #15-4, Ring #4, #4x6, #10x15, #12x6
C$53.00
All kilns should be vented to the outside. The Bailey Single Fume Vent System is a direct fume system designed to pull fumes from the firing chamber before they can leak into the studio.
C$955.00
Handle for Cone Art Kilns - all models. Screws included.
C$7.00
Cone Art uses premium “KA1” resistance wire. Each heating element is designed with a specific function in mind. Gauge of wire, watt load, and stretch ratio are all precisely calculated, to ensure maximum efficiency.
C$46.50
You can upgrade from the standard VentMaster to the Controller Integrated Orton VentMaster when you purchase your kiln. It’s the same great vent, but hardwired to your kiln (it does not require a separate power source).
C$1,180.00
Replacement wire for your Bead Tree. 2" long, sold in sets of 12 pieces.
C$17.85
Tile rack for 8" earthenware or other non-vitreous tiles up to 8" square.
Due to its fragility, this item is subject to a $25.00 packing fee for shipping. This fee does not apply to pick up orders.
Due to its fragility, this item is subject to a $25.00 packing fee for shipping. This fee does not apply to pick up orders.
C$62.50
C$62.50
A wiring harness is a complete kit of every wire and connector in your kiln, pre-cut to size, colour coded, labelled, and with connectors crimped on at the factory.
C$120.00
Cone Art uses premium “KA1” resistance wire. Each heating element is designed with a specific function in mind. Gauge of wire, watt load, and stretch ratio are all precisely calculated, to ensure maximum efficiency.
C$93.75
Cone Art uses premium “KA1” resistance wire. Each heating element is designed with a specific function in mind. Gauge of wire, watt load, and stretch ratio are all precisely calculated, to ensure maximum efficiency.
C$76.90
Cone Art uses premium “KA1” resistance wire. Each heating element is designed with a specific function in mind. Gauge of wire, watt load, and stretch ratio are all precisely calculated, to ensure maximum efficiency.
C$56.45