A sample of 15 of The Ceramic Shop's top sellers. 1 each of the stilts shown in picture, as follows:
#0, #1, #2, #4, #6, #8, #3B, #4B, #5B
#6H, #15-4, Ring #4, #4x6, #10x15, #12x6
Showingof 105 item(s)
Our furniture kits are specific to each model and contain full shelves, half shelves, a variety of posts and kiln wash.
Select your kiln from the models below:
Select your kiln from the models below:
C$35.00
This Mineral Board is rated to 1900F and each 3.3 square foot piece measures 12" x 39.5" x 1".
C$59.00
The Genesis 2.0 controller uses touch screen technology, graphical displays, has built in diagnostics, and can calculate your cost per firing. Being wifi enabled means available software updates, and communication with your smart phone.
C$935.00
Relays are available in 12 volts, 208 volts, and 240 volts. The most common relay on a kiln with an electronic controller is the 12 volt version.
C$45.00
Cone Plaques (holders) are designed to hold the cones at exactly the right angle so that they bend at the correct amount of heat work giving you accurate information about your firing.
C$3.40
Replacement wire for your Large Bead Rack. 10" long, sold individually.
C$12.10
Use stilts to keep your fully glazed wares from sticking to the shelf during the firing process. Measurements are from metal point to metal point. Made in the USA.
C$2.10
Kiln Shield is the simple, effective solution that protects your kiln’s most vulnerable area—extending the life of your kiln and saving you hundreds in repairs. It’s easy to install, doesn’t interfere with firings, and is trusted by potters.
C$275.00
A wiring harness is a complete kit of every wire and connector in your kiln from your elements to relays, your terminal block to relays, transformer and 0.5Amp breaker. These are pre-cut to size, colour coded, labelled, and with connectors crimped on at t
C$315.00
Type S thermocouples are rated for approximately 3000F and therefore are literally capable of lasting forever in a pottery or glass kiln application.
C$495.00
ONLY TO BE USED IN SQUARE KILNS. Cone Art uses premium “KA1” resistance wire. Each heating element is designed with a specific function in mind. Gauge of wire, watt load, and stretch ratio are all precisely calculated, to ensure maximum efficiency.
C$85.00
Switch wire per foot . Available in 12 Gauge in Red, White and Black. Specify colour in the notes section at checkout.
C$3.55
Kiln Shield is the simple, effective solution that protects your kiln’s most vulnerable area—extending the life of your kiln and saving you hundreds in repairs. It’s easy to install, doesn’t interfere with firings, and is trusted by potters.
C$275.00
A wiring harness is a complete kit of every wire and connector in your kiln, pre-cut to size, colour coded, labelled, and with connectors crimped on at the factory.
C$240.00
This is a Kiln Wash for use specifically in Glass Kilns. Kiln Wash is used to protect kiln shelves.
C$4.25
These handy refractory strips are designed to better distribute the weight of heavy loads and prevent damage to your kiln floor. Each strip is 1x1x6”.
C$2.75
Our kiln shelves are made from a refractory mix that is high in alumina and are rated for use up to cone 11 in oxidation or reduction atmospheres.
C$54.75
You can upgrade from the standard VentMaster to the Controller Integrated Orton VentMaster when you purchase your kiln. It’s the same great vent, but hardwired to your kiln (it does not require a separate power source).
C$1,180.00
The Cone Art Kilns maintenance kits are designed to be the kiln equivalent of a home First Aid Kit - they contain just enough of the most important parts of your kiln to ensure no break down has to mean lost firings. Select from the models listed below:
C$310.00