Showingof 104 item(s)
Our kiln shelves are made from a refractory mix that is high in alumina and are rated for use up to cone 11 in oxidation or reduction atmospheres.
C$19.25
Our furniture kits are specific to each model and contain full shelves, half shelves, a variety of posts and kiln wash.
Select your kiln from the models below:
Select your kiln from the models below:
C$39.50
Kiln Wash is used to protect kiln shelves from glaze drips and pottery from sticking to the shelves. This kiln wash is design for use on Pottery Kilns.
C$4.25
Used for pinning elements, making your own elements, or as hooks for hanging plates, wall plaques, etc...high temperature element wire is handy and will endure the temperatures of your firing. It is available in several gauges.
C$3.40
Type K thermocouples are the standard in Cone Art and most other electric kilns with controllers.
C$34.50
Made from the same reliable formula as our regular high alumina shelves, these shelves are also rated for cone 10 but are 35% lighter. Item may not be exactly as shown in photo - read full description.
C$103.00
K23 soft firebricks are commonly used as the primary insulator in electric pottery and glass kilns, raku kilns, and farrier forges.
C$12.15
The Cone Art Kilns maintenance kits are designed to be the kiln equivalent of a home First Aid Kit - they contain just enough of the most important parts of your kiln to ensure no break down has to mean lost firings. Select from the models listed below:
C$310.00
Vesuvius Super 3000 Cement is a premixed air and heat setting mortar which withstands temperatures up to 3000 degrees and resists freezing down to zero.
C$22.50
Standard (Large) Pyrometric Cones allow users a practical method to monitor the heatwork (the effect of temperature and time at temperature) inside their kiln.
C$27.95
Ceramic Element Lead Out Insulator Tube. 3.5” for Pottery Kiln, 2.5” for Glass Kiln - make your selection below:
C$4.95
Our kiln posts are rated up to cone 11 in oxidation or reduction atmospheres. These 1-3/4" square posts range from 1/2" to 12" in height.
C$2.40
Use stilts to keep your fully glazed wares from sticking to the shelf during the firing process. Measurements are from metal point to metal point. Made in the USA.
C$2.10
Type S thermocouples are rated for approximately 3000F and therefore are literally capable of lasting forever in a pottery or glass kiln application.
C$425.00
Cone Art uses premium “KA1” resistance wire. Each heating element is designed with a specific function in mind. Gauge of wire, watt load, and stretch ratio are all precisely calculated, to ensure maximum efficiency.
C$91.50
The Orton VentMaster vents the fumes directly from the kiln before they exit the kiln into the room. This is a very effective venting system which we highly recommend with every kiln.
C$1,025.00
Relays are available in 12 volts, 208 volts, and 240 volts. The most common relay on a kiln with an electronic controller is the 12 volt version.
C$45.00
* Please see notes at bottom of page before ordering.*
Tube Assembly for Dawson Kiln Sitter.
Tube Assembly for Dawson Kiln Sitter.
C$95.00
Cone Art uses premium “KA1” resistance wire. Each heating element is designed with a specific function in mind. Gauge of wire, watt load, and stretch ratio are all precisely calculated, to ensure maximum efficiency.
C$106.65
These handy refractory strips are designed to better distribute the weight of heavy loads and prevent damage to your kiln floor. Each strip is 1x1x6”.
C$2.75
The Bartlett controller offers precise control and many features not available with other controllers. It comes with preset firing profiles, allowing you to fire by simply entering a cone number, as well as the option of user-defined programs.
C$620.00